Fascia wrapping
Metal wrap can be added over new or sound fascia once any rot is gone.
Exterior Services
Fascia Repair Dover, NJ
A roofer in Dover can repair or replace rotted fascia boards, reattach sagging gutters and fix the drip edge that keeps water off the wood, once the source of the water is found. One call to (862) 430-1002 reaches a nearby roofer who handles fascia repair.
The fascia sits right where water leaves the roof, so it is the first trim board to rot when that water goes the wrong way. Without a drip edge lapped into the gutter, runoff clings to the roof edge and wets the top of the fascia every storm. The wood slowly loses strength until the gutter spikes or hanger screws no longer hold.
Rotted fascia is often the visible part of a bigger problem. Behind the board are the rafter tails, the roof decking at the edge and the soffit, and water that gets past the fascia soaks into all of them. Aluminum wrap over wood can hide all of this, since the metal looks fine while the board behind it crumbles.
It helps to know what you are seeing before you call. Note where paint is peeling, where gutters sag or have pulled away, and whether water pours over the gutter in heavy rain. Say whether the fascia is bare wood, painted, PVC or wrapped in metal, since that changes the repair.
If the problem goes deeper than it first looked, a Dover roofer may also recommend soffit repair or gutter installation.
Need fascia repair in Dover? Call (862) 430-1002 to reach a nearby roofing contractor.
Call nowThe process
What happens during a fascia repair
Here is how a roofer typically handles a fascia repair.
Inspect the roof edge
The visit starts with where the water comes from, usually a missing drip edge, a clogged gutter or a gutter with the wrong slope. Probing along the board shows where the rot starts and stops.
Free the board
To reach the fascia, the gutter over it is removed and the hangers pulled. Worn spikes are replaced with hidden hangers and screws.
Check the rafter tails
The roofer looks at the rafter ends and the sub-fascia, since soft framing will not hold a new board. This is the step that decides whether the repair lasts.
Fit the board
A replacement board matched to the existing size goes up, sealed at the ends and joints. Wood is primed on every side, including cut ends, before it goes up.
Reset the drip edge
A drip edge is added or reset so it laps over the back of the gutter and throws water clear of the fascia. Without it, the same board will rot again.
Rehang the gutter
Gutters are rehung on the new fascia with a slight slope toward the outlets. The board is painted to match if it is wood.
What is included
Common fascia repairs
Rafter tail repair
Rotted rafter ends behind the fascia are sistered or rebuilt so the new board stays put.
Soft fascia
Damaged fascia is replaced with primed wood or PVC and scarfed into the existing board.
Edge flashing
Drip edge is added where the roof edge had none which stops the rot from coming back.
Gutter rehanging
Sagging gutters are rehung on solid fascia with new hangers so they drain instead of overflowing.
Related service
Fascia Board Replacement Dover, NJ
When rot runs along most of a wall, or the boards are split and warped end to end, replacing the full run of fascia is the cleaner fix. The gutters come down, the old boards come off and the rafter tails behind them are checked before new boards go up. The choice of material affects upkeep, since wood needs paint while PVC and wrapped boards do not.
In Dover, fascia board replacement often lines up with a new roof or new gutters, since the roof edge is already being worked on. Be wary of any plan that covers rotted boards with metal instead of replacing them. Also ask about the size of the new boards, since fascia that is too narrow can leave gaps at the soffit and gutter.
Related service
Fascia Board Repair Dover, NJ
Localized fascia damage, often at corners and below gutter joints, can usually be repaired without replacing the whole board. The new piece is joined with an angled scarf joint so the seam is strong and less likely to open. Minor surface damage may only need consolidant, filler and paint.
Patching a fascia board in Dover without fixing the gutter or drip edge above it just buys a season or two. Common fixes include a resealed gutter joint, a cleared outlet or a new length of drip edge. Sealed and painted, the patch holds up like the original wood.
Local help
Fascia Repair Near Me
Around Dover, fascia rot usually shows up behind gutters that overflow or along roof edges built without drip edge. Across Dover and nearby communities including Wharton, Rockaway, Mount Arlington and Morris Plains, the fascia under trees and heavy gutter loads is the first to go, which is why keeping gutters clear does so much to protect the fascia.
For fascia repair in Dover, NJ or nearby towns like Wharton, Rockaway, Mount Arlington and Morris Plains, call (862) 430-1002 to reach a roofer who covers your street.
What the local climate does to a roof
Winters here are long and cold, with snow on the roof for weeks at a time and plenty of nights below freezing. When warm attic air melts the snow, the meltwater runs down and freezes again at the eaves, building ice dams that push water up under the shingles. Coastal storms and heavy spring rain drive water sideways into flashing, valleys and old chimneys. Most homeowners in Dover, NJ have the roof checked in the fall and again after the snow melts.
Why call
Why act early
Drier ceilings
A roof problem fixed early rarely spreads to the decking, the insulation or the ceilings.
Familiar with local homes
Local roofers see the same roofs and storm damage across Dover and nearby towns.
Know what happens next
Ask the roofer about the cause, the options and the estimate before work starts.
Fascia Repair questions
Why do gutters pull away from the fascia?
The fascia is what gutters are fastened to. When the wood softens, hanger screws and spikes lose grip and the gutter sags, tips forward or pulls away. Repairing the fascia and rehanging the gutter with hidden hangers fixes both problems at once.
Which fascia material lasts longest?
Rot-proof materials such as PVC and composite last longest. Primed wood is easy to match on older homes but needs regular paint. Whatever you choose, a proper drip edge and working gutters matter more than the board itself.
What causes fascia boards to rot?
Most fascia rot traces back to the roof edge and the gutters. A missing drip edge, clogged gutters and leaking gutter seams all keep the wood wet after every rain. Peeling paint and unsealed cut ends speed up the damage.
Can fascia be repaired instead of replaced?
Repair is fine when damage is limited to a few spots and the rafter tails are sound. If the damage is widespread, new boards end up being the simpler fix. The roofer will probe the wood to see which option fits.
Is it safe to wrap rotted fascia in aluminum?
Covering rotted wood with aluminum hides the rot instead of stopping it. The gutter hangers still screw into the wood behind the wrap, so they loosen as the board softens. Fix the wood, then add wrap over it.
More questions? Call (862) 430-1002
Related services
Soffit Repair
Repairs for rotted, sagging or loose soffit panels under the roof eaves, matched to what is causing the damage in the first place.
Learn moreGutter Installation
Gutter installation that carries roof water away from the siding, fascia and foundation, with the fascia checked before anything is hung.
Learn moreGutter Repair
Repairs for leaky joints, bad pitch, loose hangers and damaged downspouts, without replacing gutters that still have life in them.
Learn moreRoof Repair
Fixing the shingles, flashing, boots and decking that let a roof down, matched to what is actually wrong up top.
Learn more
Looking for something else?
See all roofing servicesGet fascia repair help in Dover
Call (862) 430-1002 for a local roofer in Dover and nearby towns.